SpacePlanner logoSpacePlanner

Building features

How to add a roof: pitched, flat or pergola

A roof is an outline on the plan. SpacePlanner works out the ridges, hips and valleys from that outline and builds the roof in 3D. On the 2D plan you see it as dashed lines.

The Roof tool starts with three choices. Flat and Pitched put a roof on your outside walls in one click; it follows the walls and moves when they move. Draw outline is for a roof that covers only part of the house, or has a shape of its own.

When you add a floor on top, the roof moves up to the new top floor for you.

Open the Roof panel

  1. Go to the right floor

    A roof sits on the walls of the floor you are on. For the main roof, switch to the top floor first with Floors in the top bar or Alt+Up.

  2. Open Roof

    Press Shift+R, or click Roof in the left toolbar under Structure. It starts with a small choice: Flat, Pitched or Draw outline. Once the floor has a roof, the Roof panel opens with its settings.

    The Roof panel with the Use my walls and Draw roof outline buttons
  3. Switch floors if asked

    If you are not on the top floor, the panel says Roofs usually go on the top floor. Switch to and the floor name. Click Switch for the main roof. Stay where you are for a porch or a single storey part.

Add a flat or pitched roof on your walls

  1. Click Flat or Pitched

    Click Flat for a flat concrete roof, flush with the walls. Click Pitched for a gable roof with a 45 cm overhang. The roof appears over the outside walls and follows them, so it updates when you move them. You can change the type afterwards.

  2. Close the walls first if needed

    If you see Your walls don't close a shape yet, the outside walls have a gap. Close it, or draw the roof outline instead.

  3. Edit the corners by hand

    To reshape a wall roof yourself, select it and click Edit its corners instead. It stops following the walls and becomes a drawn outline.

Draw a roof outline

  1. Click Draw outline

    Click Draw outline. The panel steps aside on your first click on the plan, so you can see what you are tracing.

  2. Click each corner

    Click the corners of the roof one by one. Corners snap to the outer wall corners and outer wall faces, shown by the badges Outer corner and Outer face. Pink guides line a corner up with other corners.

    Tracing a roof outline on the plan, with a corner snapped to an outer wall corner
  3. Use Shift and Alt

    Hold Shift to lock the edge to 45 degree steps. Hold Alt to place a corner freely, without snapping.

  4. Close the outline

    Click the first corner again to close the shape. A roof needs at least three corners. The panel comes back with the new roof selected.

Choose the style, pitch and overhang

  1. Pick a type

    Under Type, choose Hip (slopes on every side), Gable (upright ends on each wing), Shed (one slope), Flat concrete, Timber deck, Metal sheet or Pergola (open timber slats).

    Roof settings with the roof types, Pitch and Eaves overhang sliders
  2. Set the pitch

    For a pitched roof, drag Pitch (5 to 55 degrees).

  3. Set the overhang

    Drag Eaves overhang (0 to 120 cm). A new pitched roof starts at 45 cm. A new flat roof starts flush with the walls at 0.

  4. Set the eave height

    Eave height is where the roof starts, measured from this floor. Auto sits it on top of the walls. Type a height to raise or lower just that roof, and click Use auto to go back. The floor and the walls never move.

  5. Choose the inside finish

    Inside finish sets what you see from the rooms below, the ceiling side of the roof. As outside keeps the tiles. Pick Paint with any colour, Wood boards (light, medium or dark, running up the slope), Exposed beams (rafters about every 60 cm and a ridge beam, over paint or wood boards, in natural wood, dark or painted white) or Concrete. A flat roof offers paint, wood boards and concrete. The outside never changes, and you see it from inside in 3D, in walk mode and in renders.

  6. Add a porch roof

    Draw the porch outline against the house wall and give it a lower Eave height. The edge against the taller wall gets no overhang, the wall stays solid above it, a Shed rises toward the wall and a Gable puts its gable end on the wall.

  7. Add a chimney

    Open the furniture library, pick Chimney under Structure (or search "chimney"), and place it. Set its width, depth, Height and Elevation off floor in the panel, and a brick or stone Finish. A chimney standing inside a roof face cuts a clean hole through it.

  8. Fit the inside walls to the roof

    Building an attic? Click Fit walls to roof at the bottom of the Roof panel. Every interior wall on this floor that stands under the roof then runs up to the roof's underside, following the slope, with a peak where it crosses under the ridge. The outer walls that carry the roof keep their height. The walls follow the roof from then on: change the pitch, the type or the eave height and they update. To set one wall on its own, pick To roof under Wall height in the wall panel.

  9. Set the ridge direction

    On a gable roof, Ridge runs can be Auto, Left-right or Up-down. On a shed roof it sets where the high side runs, and on a pergola which way the slats run. A hip roof follows the outline, and a flat roof has no ridge.

  10. Set thickness and colour

    A flat roof has a Slab thickness. Pitched roofs have a Tile colour, other roofs a Colour.

  11. See it in 3D

    Click See in 3D. Switch Roof off in the 3D toolbar at the bottom to look inside, and on again to bring it back.

    A house with a hip roof in the 3D view

Add dormers and roof terraces

  1. Select a pitched roof

    Open the Roof panel and pick a hip, gable or shed roof. Under Dormers and roof terraces, choose the slope to work on: N, E, S or W is the side of the plan it faces.

  2. Add a dormer

    Click Add dormer. It goes on the chosen slope with a window in its front wall, and the main roof gets a matching opening. To change the window, click it under Window type: a window selector opens with a search box and the same window catalog the walls use (Twin Casement by default). Click one to use it; it is sized to fit the front wall. Pick Gable, Shed or Flat, then set Width, Front wall height (from where it meets the roof up to its eaves) and, for gable and shed dormers, Dormer roof pitch. Its roof always meets the main roof; a dormer too tall for its slope is cut down to fit under the ridge.

  3. Move it on the slope

    On the plan, with the Roof panel open, click a dormer to select it and drag it: it slides along the slope and stays on the roof. Drag the square handle on either side to change its width, and the one at its back to change how far it reaches up into the roof (its front wall grows with it). While you drag, its outline is green where it fits and red where it does not, with the reason (over the eaves, off the roof, too close to the ridge, or overlapping another dormer or terrace). Dashed lines show the distances to the eave, the ridge, the sides of the slope and the nearest other dormer or terrace. Released in a red spot, it lands on the green spot shown nearby, or goes back where it was if there is none. A roof terrace drags the same way: a rectangle has handles on its corners and edges for width and depth, any other shape a handle on every corner. Each drag snaps to the grid and is one undo step. The sliders do the same: drag Along the slope to slide it sideways and Up from the eaves to move it up or down the roof. Add as many as you like per slope, and use the copy and bin buttons on each card to Duplicate or Delete one. A copy lands beside the original.

  4. Add a roof terrace

    Click Add roof terrace for a rectangle cut into the slope, or Draw a roof terrace on the plan and click its corners on the slope, then the first corner to close it. The roof gets a hole there, with a terrace floor, walls back into the roof (a back wall up to the roof, side walls following the slope) and a Railing on the open side. A terrace can run across a hip or a valley, or over the ridge: each slope gets its own cut and walls.

  5. Set the terrace up

    On its card, set Width, Depth up the slope, Along the slope and Up from the eaves, and Terrace floor height, measured from the floor the roof sits on. Leave it empty for auto: on that floor when the roof sits on low knee walls, at the eaves otherwise.

  6. See them everywhere

    Dormers and roof terraces show on the plan with the roof layer, in building elevations, in section views (their walls, roof, floor and railing are cut where the section line crosses them), in 3D and in the DXF export, on the layer SP_ROOF_OPENINGS.

Reshape or delete a roof

  1. Select the roof

    With the Roof panel open, click the roof in its list, or click the roof outline or overhang on the plan. You can also click it in 3D.

  2. Drag, add or remove corners

    Drag a corner on the plan to reshape a drawn roof. Alt-click an edge to add a corner. Alt-click a corner to remove it.

  3. Delete it

    Click Delete this roof, or press Delete with the roof selected.

Tips

  • For a house with a lower wing, draw the main roof on the top floor and the lower roof on the floor it covers. Its corners snap to the upper floor's facade, so it butts neatly against it.
  • The Show switch in the Roof panel hides or shows all roofs of that floor. The Roof layer in Layers controls the dashed outline on the plan.
  • Roofs appear in building elevations and in exports. Untick Roof outline in the export dialog to leave the outline off a plan sheet.
  • Clicking elsewhere on the plan closes the Roof panel.
  • Add a floor above the top floor with Copy outer walls from this floor, or Duplicate the top floor, and the roof moves up to the new top floor. A message says so, with Undo. An Empty floor above keeps the roof where it is and offers Move up, so you can move it once the new floor has walls.

Common problems

Flat or Pitched does nothing, or the button is greyed out
Your outside walls do not close a shape yet. Look for a gap at a corner and close it, or use Draw outline.
The roof shows through the floor above in 3D
The roof sits on a lower floor, for example after you added an empty floor above. Use Move up if it is offered, or delete it, switch to the top floor and add it there. Keep lower roofs only for parts the floor above does not cover, like a porch.
The roof is flat even though I picked a pitched type
Some outlines cannot carry a pitched roof, so the roof is drawn flat, as in 3D. Simplify the outline or split it into two roofs.
A dormer or roof terrace disappeared or looks cut off
A dormer stands on the slope under the middle of its front wall and may reach over a hip onto the next slope; a terrace may span several slopes. Whatever runs past the edge of the roof is cut to it, and its card says so. If it has left the roof entirely, the card says that too: move it back with Along the slope and Up from the eaves, or drag it on the plan.
The outline does not close
Click exactly on the first corner. Press Esc to cancel and start again.

Related topics

Planning a whole project?

Try it on a real plan

Free, in your browser. No sign-up needed to start.

Try it on an example house